feat(klipper): deploy printer configs

klipper/ender3v3se.cfg

@@ -1,167 +0,0 @@
-[bltouch]
-control_pin:PC13
-pin_move_time:0.400000
-probe_with_touch_mode:true
-sensor_pin:^PC14
-speed:20
-stow_on_each_sample:false
-x_offset:-23.000000
-y_offset:-14.500000
-z_offset:2.1
-
-[dirzctl]
-
-[e3v3se_display]
-language:english
-logging:true
-
-[output_pin beeper]
-pin:PB0
-
-[extruder]
-control:pid
-dir_pin:PB3
-enable_pin:!PC3
-filament_diameter:1.750000
-heater_pin:PA1
-max_extrude_only_distance:100.000000
-max_temp:260
-microsteps:16
-min_temp:0
-nozzle_diameter:0.400000
-pid_Kd:134.351000
-pid_Ki:1.371000
-pid_Kp:27.142000
-rotation_distance:7.440000
-sensor_pin:PC5
-sensor_type:EPCOS 100K B57560G104F
-step_pin:PB4
-
-[fan]
-pin:PA0
-
-[filter]
-
-[heater_bed]
-control:pid
-heater_pin:PB2
-max_temp:100
-min_temp:0
-pid_kd:1301.702000
-pid_ki:0.846000
-pid_kp:66.371000
-sensor_pin:PC4
-sensor_type:EPCOS 100K B57560G104F
-
-[heater_fan hotend_fan]
-pin:PC1
-
-[hx711s]
-sensor0_clk_pin:PA4
-sensor0_sdo_pin:PC6
-
-[mcu]
-restart_method:command
-serial:/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
-
-[printer]
-kinematics:cartesian
-max_accel:2500
-max_velocity:250
-max_z_accel:100
-max_z_velocity:5
-square_corner_velocity:5.000000
-
-[prtouch]
-clr_noz_len_y:15
-clr_noz_start_x:15
-clr_noz_start_y:25
-s_bed_max_temp:60
-s_hot_max_temp:200
-s_hot_min_temp:160
-sensor_x:32
-sensor_y:30
-show_msg:true
-wipe_retract_distance:2
-
-[safe_z_home]
-home_xy_position:134,123
-speed:150
-z_hop:10
-z_hop_speed:10
-
-[screws_tilt_adjust]
-horizontal_move_z:10.000000
-screw1:54.5,45.5
-screw1_name:front left screw
-screw2:224.5,45.5
-screw2_name:front right screw
-screw3:224.5,215.5
-screw3_name:rear right screw
-screw4:54.5,215.5
-screw4_name:rear left screw
-screw_thread:CCW-M4
-speed:50.000000
-
-[stepper_x]
-dir_pin:!PB9
-enable_pin:!PC3
-endstop_pin:~!PA5
-homing_speed:80
-microsteps:16
-position_endstop:-6
-position_max:230
-position_min:-6
-rotation_distance:40
-step_pin:PC2
-
-[stepper_y]
-dir_pin:PB7
-enable_pin:!PC3
-endstop_pin:~!PA6
-homing_speed:80
-microsteps:16
-position_endstop:-14
-position_max:230
-position_min:-14
-rotation_distance:40
-step_pin:PB8
-
-[stepper_z]
-dir_pin:!PB5
-enable_pin:!PC3
-endstop_pin:probe:z_virtual_endstop
-homing_retract_dist:2.000000
-homing_speed:4
-microsteps:16
-position_max:250
-position_min:-3
-rotation_distance:8
-second_homing_speed:1
-step_pin:PB6
-
-[tmc2208 stepper_x]
-interpolate:true
-run_current:0.600000
-sense_resistor:0.150000
-uart_pin:PB12
-
-[tmc2208 stepper_y]
-interpolate:true
-run_current:0.600000
-sense_resistor:0.150000
-uart_pin:PB13
-
-[tmc2208 stepper_z]
-interpolate:true
-run_current:0.800000
-sense_resistor:0.150000
-uart_pin:PB14
-
-[bed_mesh]
-algorithm:bicubic
-horizontal_move_z:5
-mesh_max:207,215.5
-mesh_min:30,30
-probe_count:5,5
-speed:120