mirror of
https://github.com/gensokyo-zone/infrastructure.git
synced 2026-02-09 04:19:19 -08:00
207 lines
3.4 KiB
INI
207 lines
3.4 KiB
INI
[bltouch]
|
|
control_pin:PC13
|
|
pin_move_time:0.400000
|
|
probe_with_touch_mode:true
|
|
sensor_pin:^PC14
|
|
speed:10
|
|
lift_speed:40
|
|
samples:2
|
|
stow_on_each_sample:false
|
|
|
|
# stock values from an example config
|
|
x_offset:-23.000000
|
|
y_offset:-14.500000
|
|
|
|
# arc X/Y PROBE attempt #1 (unlikely to be perfect...)
|
|
#x_offset:-24.8
|
|
#y_offset:-16
|
|
|
|
[dirzctl]
|
|
|
|
[e3v3se_display]
|
|
language:english
|
|
logging:true
|
|
|
|
[output_pin beeper]
|
|
pin:PB0
|
|
|
|
[extruder]
|
|
control:pid
|
|
dir_pin:PB3
|
|
enable_pin:!PC3
|
|
filament_diameter:1.750000
|
|
heater_pin:PA1
|
|
max_extrude_only_distance:100.000000
|
|
max_temp:260
|
|
microsteps:16
|
|
min_temp:0
|
|
nozzle_diameter:0.400000
|
|
pid_Kd:134.351000
|
|
pid_Ki:1.371000
|
|
pid_Kp:27.142000
|
|
rotation_distance:7.440000
|
|
sensor_pin:PC5
|
|
sensor_type:EPCOS 100K B57560G104F
|
|
step_pin:PB4
|
|
# https://www.klipper3d.org/Pressure_Advance.html
|
|
#pressure_advance:0.0295
|
|
pressure_advance:0.0432
|
|
#pressure_advance:0.0444
|
|
pressure_advance_smooth_time:0.040
|
|
|
|
[firmware_retraction]
|
|
retract_length:1.2
|
|
unretract_extra_length:0
|
|
retract_speed:40
|
|
unretract_speed:30
|
|
|
|
[fan]
|
|
pin:PA0
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
switch_pin:!PC15
|
|
|
|
[filter]
|
|
|
|
[heater_bed]
|
|
control:pid
|
|
heater_pin:PB2
|
|
max_temp:100
|
|
min_temp:0
|
|
pid_kd:1301.702000
|
|
pid_ki:0.846000
|
|
pid_kp:66.371000
|
|
sensor_pin:PC4
|
|
sensor_type:EPCOS 100K B57560G104F
|
|
|
|
[heater_fan hotend_fan]
|
|
pin:PC1
|
|
|
|
[hx711s]
|
|
sensor0_clk_pin:PA4
|
|
sensor0_sdo_pin:PC6
|
|
|
|
[mcu]
|
|
restart_method:command
|
|
serial:/dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
|
|
[printer]
|
|
kinematics:cartesian
|
|
max_accel:2500
|
|
max_velocity:250
|
|
max_z_accel:100
|
|
max_z_velocity:5
|
|
square_corner_velocity:5.000000
|
|
|
|
[prtouch]
|
|
clr_noz_len_y:15
|
|
clr_noz_start_x:15
|
|
clr_noz_start_y:25
|
|
s_bed_max_temp:60
|
|
s_hot_max_temp:200
|
|
s_hot_min_temp:160
|
|
sensor_x:32
|
|
sensor_y:30
|
|
show_msg:true
|
|
wipe_retract_distance:2
|
|
|
|
[safe_z_home]
|
|
home_xy_position:134,123
|
|
speed:50
|
|
z_hop:10
|
|
z_hop_speed:10
|
|
|
|
[screws_tilt_adjust]
|
|
horizontal_move_z:10.000000
|
|
screw1:54.5,45.5
|
|
screw1_name:front left screw
|
|
screw2:224.5,45.5
|
|
screw2_name:front right screw
|
|
screw3:224.5,215.5
|
|
screw3_name:rear right screw
|
|
screw4:54.5,215.5
|
|
screw4_name:rear left screw
|
|
screw_thread:CCW-M4
|
|
speed:50.000000
|
|
|
|
[stepper_x]
|
|
dir_pin:!PB9
|
|
enable_pin:!PC3
|
|
endstop_pin:~!PA5
|
|
homing_speed:80
|
|
microsteps:16
|
|
position_endstop:-6
|
|
position_max:230
|
|
position_min:-6
|
|
rotation_distance:40
|
|
step_pin:PC2
|
|
|
|
[stepper_y]
|
|
dir_pin:PB7
|
|
enable_pin:!PC3
|
|
endstop_pin:~!PA6
|
|
homing_speed:80
|
|
microsteps:16
|
|
position_endstop:-14
|
|
position_max:230
|
|
position_min:-14
|
|
rotation_distance:40
|
|
step_pin:PB8
|
|
|
|
[stepper_z]
|
|
dir_pin:!PB5
|
|
enable_pin:!PC3
|
|
endstop_pin:probe:z_virtual_endstop
|
|
homing_retract_dist:2.000000
|
|
homing_speed:4
|
|
microsteps:16
|
|
position_max:250
|
|
position_min:-3
|
|
rotation_distance:8
|
|
second_homing_speed:1
|
|
step_pin:PB6
|
|
|
|
[tmc2208 stepper_x]
|
|
interpolate:true
|
|
run_current:0.600000
|
|
sense_resistor:0.150000
|
|
uart_pin:PB12
|
|
|
|
[tmc2208 stepper_y]
|
|
interpolate:true
|
|
run_current:0.600000
|
|
sense_resistor:0.150000
|
|
uart_pin:PB13
|
|
|
|
[tmc2208 stepper_z]
|
|
interpolate:true
|
|
run_current:0.800000
|
|
sense_resistor:0.150000
|
|
uart_pin:PB14
|
|
|
|
[bed_mesh]
|
|
algorithm:bicubic
|
|
horizontal_move_z:5
|
|
mesh_max:207,215.5
|
|
mesh_min:30,30
|
|
probe_count:7,7
|
|
speed:120
|
|
|
|
[bed_mesh fallback]
|
|
version = 1
|
|
points =
|
|
-0.007500, 0.075000, 0.205000, 0.325000, 0.472500
|
|
-0.177500, -0.050000, 0.090000, 0.205000, 0.327500
|
|
-0.287500, -0.157500, -0.027500, 0.077500, 0.225000
|
|
-0.375000, -0.237500, -0.105000, 0.015000, 0.142500
|
|
-0.345000, -0.227500, -0.090000, 0.022500, 0.202500
|
|
x_count = 5
|
|
y_count = 5
|
|
mesh_x_pps = 2
|
|
mesh_y_pps = 2
|
|
algo = bicubic
|
|
tension = 0.2
|
|
min_x = 30.0
|
|
max_x = 207.0
|
|
min_y = 30.0
|
|
max_y = 215.48000000000002
|